Communication Modules







4G NB IOT/CAT1
Features
IM51A is an industrial LTE Cat M1 & Cat NB1 & EGPRS Module designed for use with the Brodersen RTU32 Series.
Cat M1: Max. 375Kbps (DL), Max. 375Kbps (UL)
Cat NB1: Max. 32Kbps (DL), Max. 70Kbps (UL)
EDGE: Max. 296Kbps (DL), Max. 236.8Kbps (UL)
GPRS: Max. 107Kbps (DL), Max. 85.6Kbps (UL)
IM51A

4G Modem 150 Mbps
Features
4G LTE CAT4 Modem for RTU32Series
LTE: LTE-FDD: 150Mbps (DL)/50Mbps(UL)
LTE-TDD: 130Mbps (DL)/30Mbps (UL)
UMTS: DC-HSDPA: 42Mbps (DL) HSUPA: 5.76Mbps
WCDMA: 384Kbps (DL)/384Kbps (UL)
GSM: EDGE: 296Kbps (DL)/236.8Kbps (UL)
GPRS: 107Kbps (DL)/85.6Kbps (UL)
IM51B

Lan + Serial
Features
1x Isolated RS232/RS485, configurable with 3x dipswitches
Configurable FULL/HALF Duplex and Configurable Endtermination on RS-485
1x Isolated LAN 10/100
Maximum 3 x CM02 in a configuration
CM02A

Serial Communation
Features
-
1x RS232 with all modem handshake signals (COM0)
-
2x RS232 with RX, TX, RTS and CTS signals (COM1 & COM2)
-
1x Isolated RS232/RS485, configurable with 2x dip-switches (COM3)
Maximum 3 x SP04 in a configuration
Interfaces:
1x 9-pin SUB-D male connector for COM0 – 2x RJ12 (6P6C) connector for COM1 & COM2 – 1x 3-way 3.5mm pluggable spring clamp connector for COM3 – 2x dip-switches, for COM3 configuration – 1x Dual colour LED on front for module status
SP04

ASDL Modem
Features
ADSL Port: RJ11, ADSL/ADSL2/ADSL2+
LAN (Ethernet) Port: RJ45, 10/100 Mbit/s full/half duplex auto sense
Power Supply: 24 Vdc (20-35VDC) 1KV isolation
RST Input: Pins 4-5 of 5-pin pluggable terminal block, to reset or remote on/off
LED Indicators: POWER, ON, ETHERNET, DSL, INTERNET
UCM-95

3G Modem
Features
Industrial 3G/GPRS Modem
Industrial terminal
Triple-band 850/1900/2100 MHz (3G)
Quad-band 850/900/1800/1900MHz (GSM)
UMTS, HDSPA
EDGE, GPRS
USB 2.0 Interface
Watchdog control interface
DIN rail mounting
Industrial graded modem
UCM-94

Features
Industrial PSTN Dial Modem
V.32bis (14400 baud) and V.90 (56000baud) support
Industrial graded for DIN-rail mounting
Wide supply range 12-48VDC
Optional versions for locking serial communication formats
Guaranteed compliance with Brodersen RTU Series
UCM-81/82

Configure your RTU Online
Introduction to LB2 I/O Series
The Brodersen LB2 I/O modules are designed for the RTU32M & RTU32N series. The I/O modules are in two parts, a bottom part containing the backplane bus, and a top part containing the I/O board and logic. All LB2 modules are hot swappable and equipped with a 200 MHz processor to process I/O, handle filtering, SOE, debounce, module clock and general module logic. Diagnostic variables are available for all LB2 I/O modules. Please see the module datasheets for full info.
Module firmware update is handled at the RTU level from the Brodersen WorkSuite.
Use only genuine Brodersen bus cables for connection to Brodersen RTUs and for extension of I/O module blocks. The connection cables for the LB2 backplane bus are designed to meet the power requirements and shielding to run high speed communications. The maximum overall length of a complete system is 30 meters. Each LB2 I/O module & power supply module is calculated as 2 cm. The cables are as the length indicates, e.g. UCC-610/1 count as 100 cm.
The maximum system configuration is 60 I/O modules on one LB2 Bus. If the configuration exceeds 60 I/O modules, an additional CPU is required.