Cables
GPS antenna extension cable
Ordering Code :
- UCC-611/5
- UCC-611/10
Features
- RF Cable SMA male – SMA female
- Cable Type : RG58
- Available in 5m and 10m
- Used as an extension cable for UCA-GP-2 antenna
Shielded local bus cable
Ordering Code :
- UCC-610/25
- UCC-610/50
- UCC-610/100
- UCC-610/200
Features
- Shielded local bus cable with RJ45 connector (8 wires)
- Color : Orange
- Available in 25cm, 50cm, 100cm and 200cm
- Used as an extension cables for LB2 back plane IO modules
Shielded ethernet cat.5e cable
Ordering Code :
- UCC-380
Features
- Standard shielded ethernet LAN cable with RJ45 connector (8 wires)
- Color : Black
- Available in 2m
- Used for general purpose
Unshielded local bus cable
Ordering Code :
- UCC-501
- UCC-502
- UCC-505
Features
- Standard unshielded local bus cable with RJ45 connector (8 wires)
- Color : Black
- Available in 10cm, 17cm and 50cm
- Used as an extension cable for UCL IO modules
Cross-wired shielded cat.6 cable
Ordering Code :
- UCC-381
Features
- Standard cross wired shielded ethernet LAN cable with RJ45 connector (8 wires)
- Color : Gray
- Available in 2m
- Used for general purpose
USB 2.0 A male to USB micro-B male cable
Ordering Code :
- UCC-353
Features
USB 2.0 A male to USB B male cable
Ordering Code :
- UCC-351
- UCC-352
Features
- Standard USB 2.0 A male to USB B male cable
- Color : Black
- Available in 0,5m and 1,8m
- Generally used for printer and scanners
USB to Ethernet convertor
Ordering Code :
- UCN-USB-1
Features
- USB to Ethernet 10/100 Mbit
- Color : Black
- Available in stock
- Used for connecting RTU to the PC through USB port.
DB9 female to female cable
Ordering Code :
- UCC-567
Features
- Standard DB9 female to female cable
- Color : Gray
- Available in 2m
- Used for LB2 SP04A module serial communication
Null modem DB9 female to RJ12 male
Ordering Code :
- UCC-301/0,5
- UCC-301/1,5
- UCC-301/2,5
Features
- Null modem DB9 female to male RJ12 (6 wires) cable
- Color : Gray
- Available in 0,5m, 1,5m, 2,5m
Adding IO modules in Brodersen Worksuite
Introduction to LB2 I/O Series
The Brodersen LB2 I/O modules are designed for the RTU32M & RTU32N series. The I/O modules are in two parts, a bottom part containing the backplane bus, and a top part containing the I/O board and logic. All LB2 modules are hot swappable and equipped with a 200 MHz processor to process I/O, handle filtering, SOE, debounce, module clock and general module logic. Diagnostic variables are available for all LB2 I/O modules. Please see the module datasheets for full info.
Module firmware update is handled at the RTU level from the Brodersen WorkSuite.
Use only genuine Brodersen bus cables for connection to Brodersen RTUs and for extension of I/O module blocks. The connection cables for the LB2 backplane bus are designed to meet the power requirements and shielding to run high speed communications. The maximum overall length of a complete system is 40 meters. Each LB2 I/O module & power supply module is calculated as 2 cm. The cables are as the length indicates, e.g. UCC-610/1 count as 100 cm.
The maximum system configuration is 60 I/O modules on one LB2 Bus. If the configuration exceeds 60 I/O modules, an additional CPU is required.