SFP-Transceiver

1.25Gbps SFP Transceiver, Single-Mode,10km Reach

Features

  • Supports up to 1.25Gbps bit rates
  • Hot-pluggable SFP footprint
  • 1310nm FP laser and PIN photo detector, Up to 10km for SMF transmission
  • Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
  • Compatible with RoHS
  • Single +3.3V power supply
  • Real time digital diagnostic monitoring
  •  Operating case temperature , Industrial : -40 to +85°C

1.25Gbps SFP Transceiver, Multi-Mode,2km Reach

Features

  • Supports up to 1.25Gbps bit rates
  • Hot-pluggable SFP footprint
  • 1310nm FP laser and PIN photo detector, Up to 2km for MMF transmission
  • Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
  • Compatible with RoHS
  • Single +3.3V power supply
  • Real time digital diagnostic monitoring
  • Operating case temperature, Industrial : -40 to +85°C

1.25Gbps SFP Transceiver, Multi-Mode, 550m Reach

Features

  • Supports up to 1.25Gbps bit rates
  • Hot-pluggable SFP footprint
  • 850nm VSDEL laser and PIN photo detector, Up to 550m for MMF transmission
  • Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
  • 550m transmission with 50/125µm MMF; 300m transmission with 62.5/125µm MMF
  • Compatible with RoHS
  • Single +3.3V power supply
  • Real time digital diagnostic monitoring
  • Operating case temperature, Industrial : -40 to +85°C

100BASE-T Copper SFP Transceiver

Features

  • Supports 100BASE two-way data transmission link
  • Hot-pluggable SFP footprint
  • TX Disable and RX Los/without Los function
  • Fully metallic enclosure for Low EMI
  • Lower power dissipation (0.5 W typical)
  • Compatible with RoHS
  •  +3.3V DC power supply
  • Compact RJ-45 connector assembly
  • Operating case temperature: -40 to +85°C
  • 100 BASE-T operation in host systems with SERDES interface
  • Compatible with IEEE 802. 3-2002 and IEEE802.2ab
  • Access to physical layer IC via 2-Wire serial bus

Adding IO modules in Brodersen Worksuite

Introduction to LB2 I/O Series

The Brodersen LB2 I/O modules are designed for the RTU32M & RTU32N series. The I/O modules are in two parts, a bottom part containing the backplane bus, and a top part containing the I/O board and logic. All LB2 modules are hot swappable and equipped with a 200 MHz processor to process I/O, handle filtering, SOE, debounce, module clock and general module logic. Diagnostic variables are available for all LB2 I/O modules. Please see the module datasheets for full info.

Module firmware update is handled at the RTU level from the Brodersen WorkSuite.

Use only genuine Brodersen bus cables for connection to Brodersen RTUs and for extension of I/O module blocks. The connection cables for the LB2 backplane bus are designed to meet the power requirements and shielding to run high speed communications. The maximum overall length of a complete system is 40 meters. Each LB2 I/O module & power supply module is calculated as 2 cm. The cables are as the length indicates, e.g. UCC-610/1 count as 100 cm.

The maximum system configuration is 60 I/O modules on one LB2 Bus. If the configuration exceeds 60 I/O modules, an additional CPU is required.